Ultraviolet-C Irradiation, Heat, and Storage as Potential Methods of Inactivating SARS-CoV-2 and Bacterial Pathogens on Filtering Facepiece Respirators.

The arrival of SARS-CoV-2 to Aotearoa/New Zealand in February 2020 triggered a massive response at multiple levels. Procurement and sustainability of medical supplies to hospitals and clinics during the then upcoming COVID-19 pandemic was one of the top priorities. Continuing access to new personal protective equipment (PPE) was not guaranteed; thus, disinfecting and reusing PPE was considered as a potential alternative. Here, we describe part of a local program intended to test and implement a system to disinfect PPE for potential reuse in New Zealand. We used filtering facepiece respirator (FFR) coupons inoculated with SARS-CoV-2 or clinically relevant multidrug-resistant pathogens (Acinetobacter baumannii Ab5075, methicillin-resistant Staphylococcus aureus USA300 LAC and cystic-fibrosis isolate Pseudomonas aeruginosa LESB58), to evaluate the potential use of ultraviolet-C germicidal irradiation (UV-C) or dry heat treatment to disinfect PPE. An applied UV-C dose of 1000 mJ/cm2 was sufficient to completely inactivate high doses of SARS-CoV-2; however, irregularities in the FFR coupons hindered the efficacy of UV-C to fully inactivate the virus, even at higher UV-C doses (2000 mJ/cm2). Conversely, incubating contaminated FFR coupons at 65 °C for 30 min or 70 °C for 15 min, was sufficient to block SARS-CoV-2 replication, even in the presence of mucin or a soil load (mimicking salivary or respiratory secretions, respectively). Dry heat (90 min at 75 °C to 80 °C) effectively killed 106 planktonic bacteria; however, even extending the incubation time up to two hours at 80 °C did not completely kill bacteria when grown in colony biofilms. Importantly, we also showed that FFR material can harbor replication-competent SARS-CoV-2 for up to 35 days at room temperature in the presence of a soil load. We are currently using these findings to optimize and establish a robust process for decontaminating, reusing, and reducing wastage of PPE in New Zealand.

The need to nurture Aotearoa New Zealand's healthcare workforce.

This commentary examines the ethical significance of recently published research demonstrating the extent to which healthcare workers experienced stress and increased challenges in the workplace due to inadequate access to personal protective equipment (PPE) during the first COVID-19 surge in Aotearoa New Zealand. The inadequate state of New Zealand's PPE stockpile and distribution system at the beginning of the pandemic was a critical signal, a "canary in the coalmine", of broader challenges facing the New Zealand healthcare system, particularly for healthcare worker safety and wellbeing. As New Zealand reforms its health system with the aim of improving access to and equity of care, an opportunity exists to apply critical lessons learnt from the COVID-19 pandemic about the need to prioritise the wellbeing of the healthcare workers we are dependent upon to deliver that care. Failure to apply this new knowledge will see the system similarly unprepared for future public health emergencies, which are likely to be imminent, and potentially with healthcare workers less willing to accept the burdens placed on them. The Nurture Framework, which has emerged from the voices of healthcare workers within this research, should be adopted as part of health reforms and ongoing emergency preparedness planning. Trust, transparency, respect and safety, the four values of the Framework, are fundamental for all workers who contribute their skills, knowledge and time to our healthcare organisations.

End-user acceptability of personal protective equipment disinfection for potential reuse: a survey of health-care workers in Aotearoa New Zealand.

BACKGROUND: The COVID-19 pandemic has highlighted personal protective equipment (PPE) supply, distribution, and disposal issues worldwide. Calls to conserve PPE stocks and increase supply resulted in the rapid development of potential disinfection methods, with the possibility of improvements in medical waste reduction. However, how receptive health-care workers are to PPE reuse remains unknown. We aimed to examine the views of health-care workers who used PPE during the first COVID-19 wave in Aotearoa New Zealand, in relation to acceptability of PPE disinfection and reuse. METHODS: In this multi-methods survey, health-care workers in New Zealand, were invited via a multimodal recruitment strategy to complete a survey regarding use of PPE during the first COVID-19 wave. Gender question options were male, female, gender diverse, or prefer not to say. Demographic differences in self-reported PPE reuse and acceptability were examined. The survey included closed (single-response, multi-response, ranking, and Likert-scale questions) and open-text questions. Any open-text comments were analysed with thematic analysis. The survey was built and deployed using Qualtrics software. FINDINGS: 1411 health-care workers completed the survey between Oct 7 and Nov 30, 2020. 1397 participants had gender data available (1140 [82%] female and 257 [18%] male) and 995 (74%) of 1347 were of New Zealand European ethnicity. PPE reuse was common and reported by 628 (45%) of the 1411 participants, with 396 (63%) of the 628 reporting reusing PPE multiple times in 1 day. Acceptability of the concept of PPE disinfection for potential reuse was high overall (1196 [85%] of 1411) but varied depending on the type of PPE. Thematic analysis confirmed that PPE reuse was already occurring and respondents recognised the potential benefits of reduced medical wastage and increased PPE supply. Important caveats for consideration included the availability of scientific evidence, level of negotiated risk, and trust in the organisation undertaking PPE disinfection, with clear communication about decontamination processes being crucial to acceptability. INTERPRETATION: PPE reuse occurred frequently during the first wave of COVID-19 in New Zealand. Although support for the disinfection of PPE for reuse was high, the success of any future programmes to reuse PPE will require meaningful engagement and clear communication with health-care workers. Further research into PPE disinfection safety and logistics is warranted, alongside the development of standard operating procedures and clearly communicated policies for the end user, should this more sustainable health-care practice be planned for adoption in certain settings. FUNDING: New Zealand Ministry of Business, Innovation and Employment (COVID-19 Innovation Acceleration Fund) and the Medical Assurance Society Foundation.

Learning from healthcare workers' experiences with personal protective equipment during the COVID-19 pandemic in Aotearoa/New Zealand: a thematic analysis and framework for future practice.

OBJECTIVES: Safety and welfare are critical as pandemic-related demands on the healthcare workforce continue. Access to personal protective equipment (PPE) has been a central concern of healthcare workers throughout the COVID-19 pandemic. Against the backdrop of an already strained healthcare system, our study aimed to explore the experiences of healthcare workers with PPE during the first COVID-19 surge (February-June 2020) in Aotearoa/New Zealand (NZ). We also aimed to use these findings to present a strengths-based framework for supporting healthcare workers moving forward. DESIGN: Web-based, anonymous survey including qualitative open-text questions. Questions were both closed and open text, and recruitment was multimodal. We undertook inductive thematic analysis of the dataset as a whole to explore prominent values related to healthcare workers' experiences. SETTING: October-November 2020 in New Zealand. PARTICIPANTS: 1411 healthcare workers who used PPE during surge one of the COVID-19 pandemic. RESULTS: We identified four interactive values as central to healthcare workers' experiences: transparency, trust, safety and respect. When healthcare workers cited positive experiences, trust and safety were perceived as present, with a sense of inclusion in the process of stock allocation and effective communication with managers. When trust was low, with concerns over personal safety, poor communication and lack of transparency resulted in perceived lack of respect and distress among respondents. Our proposed framework presents key recommendations to support the health workforce in terms of communication relating to PPE supply and distribution built on those four values. CONCLUSIONS: Healthcare worker experiences with PPE access has been likened to 'the canary in the coalmine' for existing health system challenges that have been exacerbated during the COVID-19 pandemic. The four key values identified could be used to improve healthcare worker experience in the future.

Hydrothermal deconstruction of single-use personal protective equipment during the COVID-19 pandemic.

To minimise the transmission of the SARS-CoV-2 virus, there has been a substantial increase in the production and usage of synthetic personal protective equipment (PPE) globally. Consequently, single-use PPE have been widely adopted without appropriate regulations for their disposal, leading to extensive environmental contamination worldwide. This study investigates the non-catalytic hydrothermal deconstruction of different PPE items, including isolation gowns, gloves, goggles, face shields, surgical masks, and filtering-facepiece respirators. The selected PPE items were subjected to hydrothermal deconstruction for 90 min in the presence of 30-bar initial oxygen pressure, at temperatures ranging between 250 °C and 350 °C. The solid content in form of total suspended solids (TSS) was reduced up to 97.6%. The total chemical oxygen demand (tCOD) and soluble chemical oxygen demand (sCOD) decreased with increasing deconstruction temperature, and at 350 °C the lowest tCOD and sCOD content of 546.6 mg/L and 470 mg/L, respectively, was achieved. Short-chained volatile fatty acids were produced after 90 min of deconstruction, predominantly acetic acid at concentrations up to 8974 mg/L. Ammonia nitrogen content (NH3-N) of up to 542.6 mg/L was also detected. Carbon dioxide (CO2) and unreacted oxygen (O2) were the main gaseous by-products at up to 15.6% (w/w) and 88.7% (w/w), respectively. The findings suggest that non-catalytic hydrothermal deconstruction is a viable option to process and manage PPE waste.

Deconstruction and Valorisation of a Mixture of Personal Protective Equipment using Hydrothermal Processing

This study used non-catalytic hydrothermal deconstruction to examine the deconstruction of a mixture of numerous PPE items, including isolation gowns, gloves, goggles, face shields, surgical masks, and filtering-facepiece respirators. A mixture of PPE items was subjected to hydrothermal deconstruction at temperatures varying between 250 °C and 350 °C and reaction times of 90 min and 180 min, respectively. A reduction of up to 95 % was attained in the total suspended solids (TSS). The total chemical oxygen demand (tCOD) and soluble chemical oxygen demand (sCOD) decreased dramatically to 703 mg/L and 480 mg/L, respectively. Volatile fatty acids, mainly acetic acid and ammonia nitrogen (NH3-N) were the primary end products with a concentration of up to 15,625 mg/L and 38 mg/L after 180 min of deconstruction, respectively. Carbon dioxide and oxygen were found to be the primary gaseous product, with a concentration of up to 14 % (w/w) for CO2 and 76 % (w/w) for O2. Further experiments were conducted at 300 °C and 350 °C to reuse process water for five cycles to demonstrate the feasibility of process water recycling. The results propose that non-catalytic hydrothermal deconstruction may potentially reduce PPE waste by minimising solid waste and water usage.

Hydrothermal deconstruction of single-use personal protective equipment: process design and economic performance.

Increased demand for single-use personal protective equipment (PPE) during the COVID-19 pandemic has resulted in a marked increase in the amount of PPE waste and associated environmental pollution. Developing efficient and environmentally safe technologies to manage and dispose of this PPE waste stream is imperative. We designed and evaluated a hydrothermal deconstruction technology to reduce PPE waste by up to 99% in weight. Hydrothermal deconstruction of single-use PPE waste was modelled using experimental data in Aspen Plus. Techno-economic and sensitivity analyses were conducted, and the results showed that plant scale, plant lifetime, discount rate, and labour costs were the key factors affecting overall processing costs. For a 200 kg/batch plant under optimal conditions, the cost of processing PPE waste was found to be 10 NZD/kg (6 USD/kg), which is comparable to the conventional practice of autoclaving followed by landfilling. The potential environmental impacts of this process were found to be negligible; meanwhile, this practice significantly reduced the use of limited landfill space.

Efficacy of Dry Heat Treatment against Clostridioides difficile Spores and Mycobacterium tuberculosis on Filtering Facepiece Respirators.

The COVID-19 pandemic has required novel solutions, including heat disinfection of personal protective equipment (PPE) for potential reuse to ensure availability for healthcare and other frontline workers. Understanding the efficacy of such methods on pathogens other than SARS-CoV-2 that may be present on PPE in healthcare settings is key to worker safety, as some pathogenic bacteria are more heat resistant than SARS-CoV-2. We assessed the efficacy of dry heat treatment against Clostridioides difficile spores and Mycobacterium tuberculosis (M. tb) on filtering facepiece respirator (FFR) coupons in two inoculums. Soil load (mimicking respiratory secretions) and deionized water was used for C. difficile, whereas, soil load and PBS and Tween mixture was used for M. tb. Dry heat treatment at 85 °C for 240 min resulted in a reduction equivalent to 6.0-log10 CFU and 7.3-log10 CFU in C. difficile spores inoculated in soil load and deionized water, respectively. Conversely, treatment at 75 °C for 240 min led to 4.6-log10 CFU reductions in both soil load and deionized water. C. difficile inactivation was higher by >1.5-log10 CFU in deionized water as compared to soil load (p < 0.0001), indicating the latter has a protective effect on bacterial spore inactivation at 85 °C. For M. tb, heat treatment at 75 °C for 90 min and 85 °C for 30 min led to 8-log10 reduction with or without soil load. Heat treatment near the estimated maximal operating temperatures of FFR materials (which would readily eliminate SARS-CoV-2) did not achieve complete inactivation of C. difficile spores but was successful against M. tb. The clinical relevance of surviving C. difficile spores when subjected to heat treatment remains unclear. Given this, any disinfection method of PPE for potential reuse must ensure the discarding of any PPE, potentially contaminated with C. difficile spores, to ensure the safety of healthcare workers.

Mixed-Methods Survey of Healthcare Workers' Experiences of Personal Protective Equipment during the COVID-19 Pandemic in Aotearoa/New Zealand.

There have been widespread issues with the supply and distribution of personal protective equipment (PPE) globally throughout the COVID-19 pandemic, raising considerable public concern. We aimed to understand the experiences of healthcare workers using PPE during the first COVID-19 surge (February-June 2020) in Aotearoa/New Zealand (NZ). This study consisted of an online, voluntary, and anonymous survey, distributed nationwide via multimodal recruitment. Reported domains included PPE supply, sourcing and procurement, fit-testing and fit-checking, perceived protection, trust and confidence in the workplace, mental health, and the likelihood of remaining in the profession. Differences according to demographic variables (e.g., profession and workplace) were examined. We undertook a descriptive analysis of responses to open-text questions to provide explanation and context to the quantitative data. The survey was completed in October-November 2020 by 1411 healthcare workers. Reported PPE shortages were common (26.8%) among healthcare workers during surge one in NZ. This led to respondents personally saving both new (31.2%) and used (25.2%) PPE, purchasing their own PPE (28.2%), and engaging in extended wear practices. More respondents in the public system reported being told not to wear PPE by their organisation compared with respondents in the private sector. Relatively low numbers of respondents who were required to undertake aerosol-generating procedures reported being fit-tested annually (3.8%), a legal requirement in NZ. Healthcare workers in NZ reported a concerning level of unsafe PPE practices during surge one, as well as a high prevalence of reported mental health concerns. As NZ and other countries transition from COVID-19 elimination to suppression strategies, healthcare worker safety should be paramount, with clear communication regarding PPE use and supply being a key priority.

Rapid Review of SARS-CoV-1 and SARS-CoV-2 Viability, Susceptibility to Treatment, and the Disinfection and Reuse of PPE, Particularly Filtering Facepiece Respirators.

In the COVID-19 pandemic caused by SARS-CoV-2, hospitals are often stretched beyond capacity. There are widespread reports of dwindling supplies of personal protective equipment (PPE), particularly N95-type filtering facepiece respirators (FFRs), which are paramount to protect frontline medical/nursing staff, and to minimize further spread of the virus. We carried out a rapid review to summarize the existing literature on the viability of SARS-CoV-2, the efficacy of key potential disinfection procedures against the virus (specifically ultraviolet light and heat), and the impact of these procedures on FFR performance, material integrity, and/or fit. In light of the recent discovery of SARS-CoV-2 and limited associated research, our review also focused on the closely related SARS-CoV-1. We propose a possible whole-of-PPE disinfection solution for potential reuse that could be rapidly instituted in many health care settings, without significant investments in equipment.